Al Covered Self-adhesive Bitumen Membrane

Al Covered Self-adhesive Bitumen Membrane

1.introduce: Aluminium Finish Self-adhesive Bituminous Waterproofing Membrane is composed of synthetic rubber like SBS,good road asphalt andviscosity increaser.with or without polyester felt. The upper surface is covered by PE film.aluminum foil film or sand; the silicon depositing release film...

Product Details

Al Covered Self-adhesive Bitumen Membrane

1.introduce:

Aluminium Finish Self-adhesive Bituminous Waterproofing Membrane is  composed of synthetic rubber like SBS,good road asphalt andviscosity increaser.with  or without polyester felt. The upper surface is covered by PE film.aluminum  foil film or sand; the silicon depositing release film is covered on the lower  surface as anti-sticking layer. Perfect waterproof system is an important  guarantee for waterproof project quality and its longstanding performance. This  adhered waterproof system is created on basis of scientific theories research  and practical project.which is scientific.advanced.applicable.reliable and  economical.


2.Product Specifications:

Product Category

N type

PY type

Thickness /mm

1.2

1.5

2.0

2.0

3.0

4.0

Upper Finish

PE、PET、D

PE、PET、D

PE、PET、D

PE、D

S

PE、D

S

PE、D

S

Unit Mass /(kg/㎡)

1.2

1.5

2.0

2.1

2.2

3.1

3.2

4.1

4.2

Thickness/mm

Average ≥

1.2

1.5

2.0

2.0

3.0

4.0

 

Minimum

1.0

1.3

1.7

1.8

2.7

3.7


3,Features:
 1) Self-adhesion without bonding agent.or  torching.
 2) Good rubber elasticity and elongation.
 3) Excellent adhesion bond.
 4) Good self-coalescence.
 5) Safe application.no pollution.
 6) Excellent waterproof and high strength.
 7) Available for wet ground.
 

4.Application:
 1) Widely used in the industrial and civil  building roofing.basement.underground.pool.tunnel.wooden & metal roofing.
 2) Specially applied in the chemical  factory.garment factory.granary.etc.
 3) Especially used in cold places.
 

5,Executive Standard:
 GB23441-2009 Self-adhesive Polymer Modified  Bitumen Waterproofing Membrane

Item      Type

PY type

N type

 

 

PE

PET

D

 

 

Soluble content(g/㎡)≥

2.0mm

1300

-

-

3.0mm

2100

 

4.0mm

2900

 

Tensile Property Tension (N/50mm)≥

2.0mm

350

-

150

200

150

200

-

3.0mm

450

600

 

 

 

 

 

4.0mm

450

800

 

 

 

 

 

Max Expansion Rate /% ≥

30

40

200

30

-

Heat Resistance

70℃, no slip, flow or dripping

70℃, slipping no more than 2mm

Low Temperature Flexibility ℃

-20

-30

-20

-30

-20

-30

-20

 

No crack

Water Tightness

0.3Mpa,120min, no leakage

0.2Mpa,120min, no leakage

-


6.Constructions - Pre-applied:
 1)Clean the substrate,water it to make sure  there is no dust,litter and no water piling up
 2)Brush the slurry or polymer cement-based  flexible waterproofing coating
 a)The layer thickness would better be  2mm-3mm when using polymer cement-based flexible waterproofing coating,noting  to press it even;Paint a chamfer of 50mm radius during substrate treatment at  reentrant corner;Brush the primer 100mm-300mm at length and width more than the  membrane
 b)The layer thickness is usually at 2mm  when using the proportion at 1 to 2 between water and slurry;Paint a chamfer of  50mm diameter during substrate treatment at reentrant corner;Brush the primer  300mm at length and width more than the membrane
 3)Strengthen detailed treatment
 4)Scaling up the membrane
 Release the lower surface separation  membrane,pave it on the waterproofing coating or slurry.The joint width should  not less than 60mm
 

7.Cautions
 7.1 Don’t install if the temperature is lower than 0 ℃.the basement is polluted.there are water or ice on basement.
 7.2 Don’t install with others construction processes at the same time.if  need to install others facilities on ready waterproof layer.take actions to protect  the waterproof layer from damage and the waterproof layer under facilities  should be reinforced.
 7.3 Don’t put any material.machines or facilities on ready waterproof  layer.and don’t touch the waterproof  layer with any sharp objects in order to prevent the waterproof layer from  damage.
 

8.Packaging,storage and shipping
 •Product is packed into  rolls with plastic wrapper
 •Avoid sunlight and  rain,store it under current and dry. The temperature should lower than 50℃,putting it upright and the stories less than 2
 •Shelf life is 1 year  under normal condition

 

 

Inquiry